2.4，适当调节送料皮带无极调速器 书本间距位置，根据开机速度和产品的需求适当调整间距，一般为2CM左右为宜。
2.4 Adjust the feed belt stepless adjuster spacing, according to the boot speed and product needs to adjust the spacing, generally about 2CM is appropriate.
2.5，利用书本先走一遍书本，查看以上各个环节书本是否输送顺畅，书本间距，毛刷位置，切刀位置是否正确合理。
2.5 Use books to go over books again, see the above link whether the smooth delivery of books, books, spacing, brush position, cutter position is correct and reasonable.
2.6，架上包背条卷料。调好中心位置，倒入胶水在胶水盆里，让胶水覆盖上胶轮一半以上位置，调好胶水厚薄调节螺母，用手拉动包背纸，穿过电眼下轴，送料轮，上胶轮定位轴，上胶下压轴，转向轴，发热棒，前面定位轴，使其始终居中为好。
2.6 Rack on the package back material. Adjust the center position, pour the glue in the glue basin, let glue cover the rubber wheel more than half of the position, adjust the glue thickness adjustment nut, hand pull package back paper, through the electric eye axis, feed wheel, rubber wheel positioning Axis, on the glue under the finale, steering shaft, heating rods, in front of the positioning axis, it is always centered as well.
2.7，手动状态下按下触摸屏手动页面的上胶水按钮（如图），包背纸一头用手拉上前定位轴，慢慢点动开关至书本包背轮组第一个轮，继续点动，让包背纸接触到书本同步一起走到最后一个包背轮。然后继续点动完成一本至后面出书为止。查看包背纸松紧度与平行度。直到切换到自动状态下开机运行完成。
2.7 Manual mode, press the manual button on the touch screen manual on the glue (Figure), the package back a hand pull the front positioning shaft, slowly switch to the book bag the first round of the back wheel set, continue to jog, let The package backing paper comes into contact with the book synchronization and goes to the last package back wheel. And then continue to complete a jog to the back of a book so far. Check the backpack tension and parallelism. Until the switch to the automatic state to complete the boot operation.
铁丝订书设备 锁线装订机 折页锁线皮壳装订维护与保养
3. Maintenance
3.1铁丝订书设备 锁线装订机 折页锁线皮壳装订每一个星期加注一次包背轮转轴位置黄油一次，让其转动自如
3.1 Once a week to add a packet back-wheel shaft position butter once, let it rotate freely
3.2，铁丝订书设备 锁线装订机 折页锁线皮壳装订工作运行30天左右加注一次机器内部传动齿轮黄油和传动链条机油一次，让其工作顺畅，减少摩擦与磨损。
3.2 Work about 30 days to add a machine internal transmission gear butter and the transmission chain oil once, let the work smoothly, reduce friction and wear.
3.3，铁丝订书设备 锁线装订机 折页锁线皮壳装订每次停机长时间不使用务必清理干净胶盆与涂胶轮上的胶水，交接班的情况下可以在控制界面上设置手动页面把胶水轮打开，让其转动，防止胶水固化，松开一点刮刀间歇，减少摩擦。
3.3 Each time the machine is not used for a long time to be sure to clean up the glue and glue on the glue wheel, the shift in case you can set the manual interface to open the glue wheel, let the rotation to prevent glue curing, Intermittent, reduce friction.
山东省
济南市 青岛市 临沂市 济宁市 菏泽市 烟台市 泰安市 淄博市 潍坊市 日照市 威海市 滨州市 东营市 聊城市 德州市 莱芜市 枣庄市
铁丝订书设备 锁线装订机 折页锁线皮壳装订