品牌：RETZ瑞茨/我们一直致力于流体控制领域的持续创新，始于2005……进口高温电磁阀为先导活塞式结构,采用杠杆散热功能，原理保证线圈和阀体彻底隔离，提高了使用温度，广泛应用于吹瓶机械、空压机、加湿设备、高温高压场合、中高温热水、中高温导热油、高温蒸汽、过热蒸汽等、电站抽气管道疏水系统和蒸发器的排气需要高温控制的系统中The RETZ high-temperature electromagnetic valve is a pilot piston type structure that uses a lever heat dissipation function to ensure complete isolation between the coil and valve body, increasing the operating temperature. It is widely used in bottle blowing machinery, air compressors, humidification equipment, high-temperature and high-pressure occasions, medium to high temperature hot water, medium to high temperature heat transfer oil, high-temperature steam, superheated steam, etc., as well as in systems that require high-temperature control for the drainage system of power station extraction pipelines and the exhaust of evaporators
进口高温电磁阀工作原理--Working principle of imported high-temperature solenoid valve
常闭式：当线圈通电时，先导阀芯吸合，先导孔打开，阀上腔卸压，活塞靠下腔介质压力推动，电磁阀打开。 当线圈断电时，先导阀芯靠弹簧复位，先导孔关闭，阀上腔由活塞节流孔增压和复位弹簧的推力，电磁阀关闭。
Normally closed: When the coil is energized, the pilot valve core is closed, the pilot hole opens, the upper chamber of the valve is depressurized, the piston is pushed by the medium pressure in the lower chamber, and the solenoid valve opens. When the coil is powered off, the pilot valve core is reset by the spring, the pilot hole is closed, and the valve upper chamber is pressurized by the piston orifice and the thrust of the reset spring, and the solenoid valve is closed.
常开式：当线圈通电时，先导阀芯靠弹簧复位，先导孔关闭，阀上腔由活塞节流孔增压和复位弹簧的推力，电磁阀关闭。 当线圈断电时，先导阀芯靠弹簧复位，先导孔打开，阀上腔卸压，活塞靠下腔介质压力推动，电磁阀打开。
注：出口端压力大于进口端压力，介质会反向导通。可安装止回阀
Normally open: When the coil is energized, the pilot valve core is reset by the spring, the pilot hole is closed, and the upper chamber of the valve is pressurized by the piston orifice and the thrust of the reset spring, and the solenoid valve is closed. When the coil is powered off, the pilot valve core is reset by the spring, the pilot hole is opened, the upper chamber of the valve is depressurized, the piston is pushed by the medium pressure in the lower chamber, and the solenoid valve opens. Note: If the outlet pressure is greater than the inlet pressure, the medium will conduct in the opposite direction. Can be installed with a check valve
进口高温电磁阀特点-- 活塞结构性能稳定；
密封采用耐高温材料，线圈外围增设散热机构;
阀塞与阀间巧妙地利用流体润滑作用，减少磨损;
阀芯均为不锈钢活塞式, 活塞环不会被介质中的杂质卡死;
进口高温电磁阀选型参数--
产品规格：1/4-4"
阀体材质：不锈钢/2025
介质温度：+300~+600℃ ~+800℃
适用压力：0-100MPa
介质温度：-200~+450℃。
环境温度：－20～＋50℃
防护性能：防水、防爆（DⅡCT5、ExdⅡCT5、ExmbⅡCT4、ExdⅡCT4）、防腐。
防护等级：IP67、IP65
阀芯材质: 均为不锈钢
接线方式：接线座式、引线式、插头式
控制方式：常开、常闭
电源电压：DC24~127V；AC36~380V
连接方式：内螺纹、法兰
适用介质：粘度：≤21m㎡/s，（大于21时需定制）气、水、油、蒸汽、燃气、腐蚀性气态或液态流体。
泄 漏 量：零
